Manual service at request. Free information.
1Wire Chip Resetter - The cheapest resetter ever!!!
I get an error message c-2451 after doing this. Do you know whats wrong?
C2451: Release new transfer belt unit.What is the value of you fuse?
I used a 80ma fuse and it gave me the code. Changed the fuse to 32ma/p fuse and trouble reseted. It worked like a charm. thx!
remove the separator finger before starting this procedure, you avoid to scrap the belt
the error for bizhub c353
muchas gracias este manuel me ayudo mucho resulto todo muy bien saludos
Thank you so much!
Hey My friends!Can anybody send to me the service manual of konica minolta bizhub C200 and bizhub 164/184.I will ever thankful to youSrimanta
i'm getting the error code c-2451. The only fuse they had was a .75 to replace the .80I've tried everything except put another fuse in. It runs and seems like it's going to go then it makes this slight gear stripping noise... pttt. then the error code. This machine also needs all 4 imaging units for about 6 months now and has run flawless without replacing them. Could this be part of it? I've checked all gears and everything including the belt spins fairly freely. Although I did find a long hair tangled in one of the belt shafts... it's all removed now.
i just replaced the .75 fuse with a .50 and same problem
HIIam urgently in need of a service manual for a bizhub C252. Getting error code C-3452 Malfunction detected. Call Tecnical Representative.......Could anyone please assist? Many thanks!
Hi, do you still need the manual, mail me at:email@example.com and I will send to you for free.bye
Good day. I saw your contact in kmc copyservice blog, I wonder if you can send me the service manual of Konica c200, I'll be very grateful.My email: firstname.lastname@example.orgMy name is Andrew Vilaça, I'm in Brazi
Basically the transfer belt and fuser fuses are a picofuse and GMA series fast blow fuse as stated here on this website you can get them at radio shack. Another cheap source for getting them online is:http://www.kopy-kat.comThey also have infinite drum chip re-setters that are cheap and work great < $100.00
Hi there, I have a Bizhub C300 but it has exactly the same set up as the pictures shown on here. I am trying to reset the Transfer Belt and have replaced it with a 80ma and a 50ma,. but neither have reset it and I get the error code C-2451. Can anyone help please?Thanks
Hello, I service these machines right here in Brazil and I've faced this problem. I solved changing the fuse for another one of 32ma.Any value higher than this give the code c-2451.It's interesting to note that values so low as theseusually have a high tolerance what make some piecesdon't work as they should.Any trouble mail me at:email@example.com you
The pictures are great! I pulled out the transfer unit and the fuse. It is now Sunday nite so I need to get the fuse replacement tomorrow. I pieced the whole thing back together and closed the door fine. Now I try to open the door and the right hand side is jammed...??
dear sir i have develop ineo +203..here appears a problem. actually when i touch the Fax button it doesnt work.. would you please let me know what is the problem with my printer¿
I just found your website and am I glad I did. As an ex Xerox tech paying for supplies that still have life in them always bothered me. I just started servicing my own Bizhub C351 and need a good supplier of supplies. Any suggestions? I also need a service manual. Thanks Ed
Although I am no genious, I fail to see why a fuse rating would affect the ability of the transfer unit working. I cannot see that the electronics would have that sensitive a board to detect the difference in resistance (Absolutely unmeasurable)between a 80milliamp and as much as a full amp fuse.Can anyone explain WHY?
The fuse is only used to reset the Transfer Belt counter. It is a way to re-use the belt instead of replacing with a brand new one.
I am enjoying very much.
hi i m amanlal dear sir plz help same time
could anyone tell me how to remove the " C " looking washer thing?I am having difficulty removing it and i don't want to use much force so i don't break it.ThanksMike
Hi guys my c353 won't reset the transfer belt and the fuser unit. a technician said it was the board what to do think can anybody help?
ICP5 is blown. replace icp5 with a normal 2,5 amp fuse.
Hi Admin, I have 2 PRCB's that need ICP5 replaced what fuse holder do you use and is it a solder on holder or does it use clip. As you can tell havent been down this road before so any help is appreciated. By the way love the blog and will check it out daily.
what is error c-4551 in a c203 bizhub
c-4551 Laser Malfunction C you need replace laser cyan but Konica recommended replace all four laser.
Maybe I can help you but this service have 52 mega
I am enjoying very much the discussions of technical and other persons questions, answers and their interest on Konica Minolta machines. With this reference I think in color machines Konica Minolta machines are best???S.M. Dutta,Assam, India
I made the switch excellent and worked perfectly, thanks
I tryed with a 31.5; 40 dnd 63ma fuses and it gave me the error code c-2451.
dear sir how to reset imaging unit model c-253
i have konica c351.i replace the fuse form image belt and i got error c2451.after a while and some reset i got error c 5356. can sombody help me?.
i changed 0.08amp with 0.05amp. works fine. thnaks
The pictures are very illustrative and clear to understand.I appreciate your balanced advice.Thanks!!!Konica Minolta Bizhub 600 Toner Cartridge
hy a use all this step, i have a bizhub c300 end after change end put on the place unit transfer say again "please change the transfer unit" end eror is c2152 can you help me some information here or email firstname.lastname@example.org
Thanks so much. Thanks to the tip I changed out the transfer unit and saved $300. It came with an ozone filter though and I can't figure out where it goes. Its a bizhub C203
The printers have become almost a necessity for both students and working professionals alike. A konica imaging units work best for your printer. People also rely to a great extent on bizub imaging unit. Apart from these, toners are also important, they provide life to the printouts, a Konica toner is a good option. An 888029 ricoh toner is also good for your cartridge.
Nice content. Please see:56UA53040 Upper Fuser Roller is a very important, fundamental and momentous division and is vigorous recognized for the grasp up to the Konica imaging unit. They in collaboration and reciprocally are helping in the go round out part and also be in motion toward and transport into engage in recreation of A03UR70711 Developer Unit. The editorial column puts vividness on the subject matter of 4049212 Transfer Belt Unit.
Hi, I'm trying to buy a new fuse for the bizhub c253 image transfer belt but I don't know what kind of fuse to get. When I tried to order it online they said I needed the amp amount, the size, and if it was "fast" or "slow". Can someone please help me out.
Dear sir, I have kmb c550 and is given me error code:P21 and P6,what is the problem and if i print it clear at the top but when it get to the middle it will fade. also is there any reset er chips for transfer belt and fuser unit and i also need service manual for this machine that also containing all the error code,i will be happy if any body can send me free service manual to my email : email@example.com
Buy bizhub pro c6500 Toner Cartridge online. Safe and secure service.
The 56UA53040 Upper Fuser Roller is a very crucial part of the copier machine. The more advanced copier machines, with all the latest parts like the konica imaging unit will be capable of dealing with various sizes of papers. There may be warranty provided with the different parts like touch screen for copier. The 4049212 Transfer Belt Unit is useful from the point of view of dynamism of the machine.
Hello sir i need service manual of bizhub c452 and bizhub c353. Please if you have send me at ( firstname.lastname@example.org). I shell be will thankfull to and pray for you may God bless you and gave u all pleasures in your life.
I have a C253 and I did it with a 35mah 250V fuse worked like a charm but I did try it with a 80 and got the C2451 also until I went with a 35mah fuse. Thanks this saves me a bundle. Ronnie Mc Baton Rouge, LA
I HAVE DVELOP 452 AND I HAVE PROBLEMS WITH THE CODE C2556 ONLY WITH THICK1 PAPER. THE MACHINE PRINTS 6 COPIES AND THEN THE CODE C2556 COMES. IF I USE PLAIN PAPER OR THICK 2 WORKS FINE!
Are you looking for Konica imaging unit? Do you want to ensure quick delivery of touch screen for copier? Parts like 4049212 transfer belt unit and more at competitive cost are 56UA53040 Upper Fuser Roller available online.
bJrQuelqu'un pourrait m'indiquer comment reinitiliser l'unite d'imagerie Magiclor MF 4690 ?Cordialement
sombody could answer me if it's possible to reset a 4690 MF Konica Minolta Transfer Belt cause ther is not fuse